Colourtex Grained
ProRend Colourtex Grained
| Packaging, kg | 17 |
| Bags, pallet | 44 |
| Water, l maximum dilution |
2% |
| Coverage, m²/bucket |
~4.5 - 5 |
| Shelf life, years | ~2 |
| Surface drying | 24 hrs |
| Through dry | 48 - 72 hrs |
Technical Data EN 998-3: 2006
| L1 - Bulk density, kg/m³ | ~1.70 |
Additional Technical Data
| Maximum grain size, mm | ~3.00 |
| Viscosity | 450 m Pas |
| pH | ~8 |
| Water absorption coefficient | W = 0.1 kg/m2 |
Technical Datasheet
| Description/ Useage- |
Ready mixed silicone based finish, manufactured from fine natural and coloured aggregates. Grained textured finish that has excellent weather, scratch and knock resistant qualities. |
| Colour- |
12 standard colours, RAL, BS, colour matching service available |
| Application- | |
| Site Work- |
Scaffolding must be independently tied, to allow uninterrupted application. Any faults must be rectified. |
| Site Conditions- |
Do not apply when substrate/ air temperature is below 5oC or above 30oC. Protect areas before and after application. |
| Substrates- |
Primed, new or old structures. Externally- May be applied to suitably smooth and flat surfaces of cement based finishing rendering, fair faced concrete, however ProRend Float is the recommended substrate. Internally- Suitably smooth and flat plasters, gypsum finishing plasters, dry lining, plywood and suitable insulating boards. |
| Preparation- |
Remove old, dusty, dirty and loose plaster and paint layers. Remove grease, dirt and organic growths. |
| Render Application- |
Apply to the backing by traditional methods. Using a stainless steel hawk and trowel, apply a tight coat to the thickness of the largest aggregate. Do not interrupt the application until a complete section is finished. After ~10-30 minutes, check the material is dry by rubbing with a smooth plastic float in either horizontal, vertical, or circular strokes depending on the pattern required. |
| Coverage- | Dependant on the substrate. Guide- when applied 3mm thick, coverage is ~4.5-5m2 per bucket. |
| Curing/ Drying- | Normally dry within several hours and throughly dry within 48-72 hours depending on the substrate and drying conditions. Suitable protection should be provided. Can stain unprotected surfaces. |
| Protection- | Cover parts which do not have to be treated with paper and tape. Remove directly after applying the primer. |
| Cleaning- |
All equipment must be cleaned immediately after use with water. Waste material should not be emptied into any drainage system. |
| Packaging- | 17kg tubs |
| Storage- | Keep in cool, dry conditions. Protect from direct sunlight and heat. Keep container closed when not in use. Do not stack more then 4 containers high. |
| Technical Data- | |
| Characteristics- | Can be finished in either vertical, horizontal or circular random grained textures to a 3mm thickness. |
| Composition- | Fine natural and special coloured aggregates in a silicone binder giving excellent adhesion and weatherproofing. Contains effective biocides to help preserve its attractive appearance. |
Safety Datasheet
1. Identification of substance
| 1.1 | Trade name: | ProRend Colourtex Grained |
| 1.2 | Supplier: | SAS (Europe) Limited |
| 1.3 | Address: | King Stag House, Cheriton Bishop, Exeter, Devon, EX6 6JE |
| 1.4 | Country: | UK |
| 1.5 | Telephone: | +44 (0) 1647 24620 |
| 1.6 | Emergency call: | +44 (0) 1647 24620 |
2. First Aid/ Fire/ Accidental Measures-
| S & R Phrases | Description | |
| Inhalation- | S23/ 22 |
Do not breathe vapour Do not breathe dust Move person into fresh air and keep warm If breathing is irregular or not at all give artificial respiration. Do not provide food or drink. If unconscious place in recovery position and wait for medical assistance. |
| Skin Contact- | S28/ 24 |
Avoid contact with skin After skin contact wash immediately with plenty of soap |
| Eye Contact- | S26/ 25 |
Avoid contact with eyes After eye contact rinse immediately with water and seek medical advice |
| Ingestion | S62/ 20/ 21 |
If swallowed, do not induce vomiting, seek medical advice and show label/ container When using do not eat, drink or smoke |
| Suitable fire agents- |
Foam CO2 Water |
|
| Protective equipment- | S36/ 37/ 39 |
Wear suitable protective clothing and gloves Wear eye/ face protection |
| Environment precautions- | S61 |
Avoid release into the environment Refer to special instructions |
| Handling- | S2 | Keep out of the reach of children |
| Storage- | S49 |
Dry store in original packaging at 5oC-30oC Protect from direct sunlight and frost |
3. Physical and chemical properties-
| Appearance- | Different colours, Viscose |
| Odour- | Weak |
| pH-value- | 9 |
| Melting point/ range- | >100oC |
| Relative density- | ~ 1.8 kg/dm3 |
| Solubility in water- | Mixable |
4. Stability and reactivity-
| Conditions to be avoided- | Avoid conditions above 60oC, direct sunlight and contact with heat sources. |
| Materials to be avoided- | Strong acid and alkali products to avoid exothermic reactions |
| Dangerous products of decomposition- | After the evapouration of water, combustion will lead to the development of CO2, CO, NOx and dense black smoke |
5. Toxicological information-
| S & R Phrases | Descriptions | |
| Inhalation- | R23/ 67 |
Toxic by inhalation Vapours may cause drowsiness and dizziness |
| Skin- | R38/ 43 |
May cause sensitisation by skin contact Irritating to skin |
| Eyes- | R36/ 41 |
Irritating to eyes Risk of serious damage to eyes |
| Ingestion- | R25 | Toxic if swallowed |
6. Ecological information-
Product can not be disposed of into sewers or waterworks.
7. Disposal consideration-
This material and its container must be disposed of as hazardous waste.
