PRORend Uniform

Colourtex Uniform

ProRend Colourtex Uniform

 

Packaging, kg 17
Bags, pallet 44
Water, l maximum dilution

2%
Coverage, m²/bucket
 ~6 - 6.5
Shelf life, years ~2
Surface drying 24 hrs
Through dry 48 - 72 hrs

 

Technical Data EN 998-3: 2006

 

L1 - Bulk density, kg/m³ ~1.70

 

Additional Technical Data

Maximum grain size, mm ~1.50
Viscosity 450 m Pas
pH ~8
Water absorption coefficient W = 0.1 kg/m2

 

 

Technical Datasheet

Description/ Useage- ProRend Colourtex Uniform is a ready mixed silicone based finish. It is a textured finish that has excellent weather, scratch and knock resistant qualities. Maintenance is minimal.
Colour-

12 standard colours, RAL, BS, colour matching service available
Application-  
Site Work- Scaffolding must be independently tied, to allow uninterrupted application. Any faults must be rectified.
Site Conditions- Do not apply when substrate/ air temperature is below 5oC or above 30oC. Protect areas before and after application.
Substrates-

Apply to primed, new or old substrates.

Externally- Apply to suitably smooth and flat surfaces of cement based rendering, fair faced concrete, exterior grade composition and cement boards. ProRend float is the recommended substrate.

Internally- smooth, flat plasters, gypsum finishing plasters, dry lining, plywood and suitable insulating boards.
Preparation- Remove old, dusty, dirty and loose plaster and paint layers. Remove grease, dirt and organic growths.
Render Application- It is essential that ProRend Colourtex Uniform is mixed before use. Add a maximum of 2% water and mix thoroughly. An electric hand mixer should be used to achieve good workability. It should be applied by an applicator with experience with this type of product. A tight coat of material is applied using a stainless steel hawk and trowel. Do not interrupt application until a complete section is finished. After ~10-30 minutes, depending on the drying conditions, the material is finished.
Coverage-

Coverage will depend upon the surface being coated. As a general guide- 1.5mm thick, coverage is ~6-6.5 m2 per bucket.
Curing/ Drying- 48-72 Hours. Protect from unfavourable weather conditions.
Protection- Cover parts which do not have to be treated with paper and tape. Remove directly after applying the primer.
Cleaning-

All equipment must be cleaned immediately after use with water. Waste material should not be emptied into any drainage system.

 
Packaging-

17kg buckets

 
Storage-

Store in cool, dry conditions at a temperature greater than 5oC. Protect from sunlight and direct heat. The container should be kept closed when not in use and do not stack more than four containers high.
Characteristics- Resists the penetration of rain water, it has excellent weather resistance and durability, whilst allowing the structure to breathe.
Composition- Fine natural and special coloured aggregates in a silicone binder give excellent adhesion and weatherproofing. It contains effective biocides to help preserve its attractive appearance.

 

 

 

 

 

Safety

1. Identification of substance

1.1 Trade name: ProRend Colourtex Uniform
1.2 Supplier: SAS (Europe) Limited
1.3 Address: King Stag House, Cheriton Bishop, Exeter, Devon, EX6 6JE
1.4 Country: UK
1.5 Telephone: +44 (0) 1647 24620
1.6 Emergency call: +44 (0) 1647 24620

2. First Aid/ Fire/ Accidental Measures-

  S & R Phrases Description
Inhalation- S23/ 22
  • Do not breathe dust
  • Do not breathe vapour
  • Move person into fresh air and keep warm
  • If breathing is irregular or not at all give artificial respiration
  • Do not provide food or drink
  • If unconscious place in recovery position and wait for medical assistance.
Skin contact- S28/ 24
  • Avoid contact with skin
  • After skin contact wash immediately with plenty of soap
Eye contact- S26/ 25
  • Avoid contact with eyes
  • After contact with eyes rinse immediately with water and seek medical advice.
Ingestion- S62/ 20/ 21
  • If swallowed, so not induce vomiting, seek medical advice and show label/ container
  • When using do not eat, drink or smoke.
Suitable fire agents-  
  • Foam
  • CO2
  • Water
Protective equipment- S36/ 37/ 39
  • Wear suitable protective clothing and gloves.
  • Wear eye/ face protection
Environment precautions- S61
  • Avoid release into the environment
  • Refer to special instructions
Handling- S2
  • Keep out of the reach of children
Storage- S49
  • Dry store in original packaging at 5oC-30oC
  • Protect from frost and direct sunlight

3. Physical and chemical properties-

Appearance- Different colours, Viscose
Odour- Weak
pH-value- 9
Melting point/ range- >100oC
Relative density- 1.8 kg/dm3
Solubility in water- Mixable

 

4. Toxicological information-

  S & R Phrases Description
Inhalation- R23/ 67
  • Toxic by inhalation
  • Vapours may cause drowsiness and dizziness
Skin- R38/ 43
  • May cause sensitisation by skin contact
  • Irritating to skin
Eyes- R36/ 41
  • Irritating to eyes
  • Risk of serious damage to eyes
Ingestion- R25
  • Toxic if swallowed

 

5. Ecological information-

Product can not be disposed of into sewers or waterworks.

6. Disposal consideration-

This material and its container must be disposed of hazardous waste. (S60)