Technical Datasheet

Description:

PROREND RAPID is especially suitable for application on mineral building substrates and aerated concrete internally or externally. This lime cement render with controlled setting time can be float sponge finished or keyed to receive a subsequent finish and provides excellent background for PROREND decorative finishes.

Composition:

A premium industrially produced dry mortar based on bonding agents of lime and approved light weight additives in accordance with DIN 18557, 18550, 4226 part 1, 459, mortar group PII, CS II in compliance with BS-EN 998-1.

Characteristics:

PROREND RAPID is a flexible render that is easy to apply by hand or machine. Due to its lightweight additives PROREND RAPID minimises surface tension between render and background substrate. It is weather resistant and a thermal insulant after curing. PROREND RAPID may be finished 2 hours after application regardless of thickness, temperature or substrate.

The setting technology creates the possibility to make accurate calculations and planning. After two hours the render is ready to be finished and is not influenced by temperature, thickness or substrate. PROREND RAPID also lowers the risk of cracking because of its low e- module and early setting.

Colours:

Grey

Technical Data

Mortar group	CSII according to DIN EN 998-1 / PII according to DIN V 18550
Binding Agent	lime and cement
Additive	Quartz, perlite
Grain size	approx. 1.0 mm
Water-mortar proportion	approx. 7 L / per 25 kg
Bulk density (volume weight)	approx. 1.3 kg/dm³
Volume weight finished product	approx. 1.2 kg/dm³
Pressure resistance	approx. 2.5 N/mm²
Bending resistance	approx. 1.0 N/mm²
E-module	approx. 2000 N/mm²
Water absorption	W2 (according to DIN EN 998-1)
Water Vapour permeability (μ)	5/20 (according to EN 1745)
Heat coefficient (λ)	0.35 (m².K/W)     P=50%     according to EN 1745 0.40 (m².K/W)     P=90%     according to EN 1745

All above value's are measured in a laboratory under set conditions, differences in practice are possible.

BS EN 13914-1: 2005

Design, preparation and practical application of external rendering and internal plastering - part 1, external rendering, should be followed at all times.

Sitework:

Scaffolding must be independently tied, to allow uninterrupted application.  Any faults in the structure, particularly those which may lead to moisture penetration, must be rectified.

Site Conditions:

Temperature range, 5-30°C.   PROREND RAPID must not be applied to frozen or thawing supports.  If the coating must be applied in adverse weather conditions, it is essential to protect both the working area and finish before and after application.

Safety Datasheet

1. Identification of substance

1.1	Trade name:	ProRend Rapid
1.2	Supplier:	SAS (Europe) Limited
1.3	Address:	King Stag House, Cheriton Bishop, Exeter, Devon, EX6 6JE
1.4	Country:	UK
1.5	Telephone:	+44 (0) 1647 24620
1.6	Emergency call:	+44 (0) 1647 24620

2. Composition/ Data on components

Chemical components	Concentration	Symb.	R-number	Cas-nr
Portland cement 65-997-15-1	5 – 30M	Xi	R36, 38, 41, 43	266-043-4
Calciumhydroxide 1305-62-0	< 10M	Xi	R38, 38, 41	215-137-3

3. Hazards identification

3.1	Hazard classification	R36	Irritating to eyes
		R38	Irritating to skin
		R41	Risk of serious damage to eyes
		R43	May cause sensitisation by skin contact

4. First aid measures

4.1	Inhalation		Move person to fresh clean air and keep warm. Avoid exertion. If the patient has irregular breathing or is not breathing give artificial respiration. Do not provide food or drink. If patient is unconscious place in recovery position and seek medical assistance immediately.
4.2	Skin contact	S28	Wash with soap and warm water and rinse thoroughly
4.3	Eyes contact	S26	Rinse opened eye for several minutes under running water. If irritation persists consult a doctor immediately.
4.4	Ingestion	S62	If swallowed, seek medical advice immediately and show this label. Rinse mouth and drink plenty of water. Do not induce vomiting.

5. Fire fighting measures

5.1	Suitable extinguishing agents	Foam, CO2, water
5.2	Specific hazards
5.3	Protective equipment

6. Accidental release measures

6.1	Individual precautions	S22	Do not breathe dust
		S24	Avoid contact with skin
		S25	Avoid contact with eye or clothes
6.2	Precautions to protect environment		Prevent product from spreading into the environment via surface water or sanitary sewer systems. Warn local authorities in case of accidental release.
6.3	Cleaning methods		Product must be disposed of according to local regulations. Soak up with inert absorbent materials e.g. sand, universal binder, sawdust.

7. Handling and storage

7.1	Handling	S2	Keep out of the reach of children.
		S22	Do not inhale dust. Use dustmask P1.
		S24	Avoid contact with skin.
		S25	Avoid contact with eyes or clothes.
7.2	Storage		Protect from moisture, frost and direct sunlight. Dry store in original packaging at 5°C – 30°C. Avoid contact with ignition sources and oxidation resources of strong acid or alkali. Open bags need to be properly sealed and stored to prevent leakage.

8. Exposure controls and personal protection

8.1	Technical measures		Follow legal requirements
8.2	Components with critical values that require monitoring at the workplace:
8.3	Personal protective equipment:
8.3.1	Respiratory	S22	Do not inhale dust. Use dustmask P1
8.3.2	Hand	S24	Avoid contact with skin
8.3.3	Eye	S25	Avoid contact with eyes. Use safety goggles
		S26	In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
		S37	Use gloves
		S39	Wear eye/face protection (safety goggles)
8.3.4	Body	S20/21	When using, do not eat, drink or smoke.

9. Physical and chemical properties

9.1	Form	Powder
9.2	Odour	Odourless
9.3	Colour	light grey
9.4	pH-value	11 – 13.5
9.5	Melting point	>100°C
9.6	Relative density	approx 1.25 kg/dm³
9.7	Solubility	in water: 3 g/dm³

10. Stability and reactivity

10.1	Conditions to be avoided	Product is stable and unreactive
10.2	Materials to be avoided	Strong acid and alkali products
10.3	Dangerous products of decomposition

11. Toxicological information

11.1	Inhalation		Acute toxicity. Exposure to concentrations in excess of MAC values to vapour of the compressed substance can damage health: irritation to mucous membrane; affections to the liver, kidneys and central nervous system. Symptoms include dizziness, tiredness, drowsiness, muscular paralysis and unconsciousness.
11.2	Skin	R38	Irritating to skin
		R43	May cause sensitisation by skin contact
11.3	Eyes	R36	Irritating to eyes
		R41	Risk of serious damage to eyes
11.4	Swallowing		Acute toxicity. Can cause nausea, stomach cramps and irritation to the mucous membrane.

12. Ecological information

No information available. Product cannot be disposed of into sewers or waterworks.

13. Disposal consideration

Product must be disposed of according to local regulations pertaining to the disposal of hazardous waste. It is not permitted to dispose of product with normal waste.

14. Transport information

14.1	ADR
14.2	RID
14.3	ADNR
14.4	IMDG
14.5	IATA

15. Regulatory information

Labelling according to CE directives: The product is not subject to identification under EU Directives and the Ordinance on Hazardous Materials: 67/548 ECC or 95/45/EC

S2	Keep out of the reach of children
S20/21	When using, do not eat, drink or smoke
S22	Do not breathe dust
S24	Avoid contact with skin
S25	Avoid contact with eyes
S26	In case of contact with eyes, rinse immediately with plenty of water and seek medical advice
S28	contact with skin, wash immediately with plenty of soap-suds
S37	Wear suitable gloves
S39	Wear eye / face protection
S62	If swallowed, do not induce vomiting; seek medical advice immediately and show this container or label
R36	Irritation to eyes
R38	Irritation to skin
R41	Risk of serious damage to eyes
R43	May cause sensitisation by skin contact

16. Other information

see technical information sheet.

*This data is based on our present knowledge. However, it shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.